Demco 800 BUSHEL Spezifikationen Seite 10

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 16
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 9
Page 10
Backplate Installation
Mount the backplate to the spindle flange. In mount-
ing the brake, be sure the hydraulic wheel cylinder is
at the top. Brakes are also marked as RIGHT and
LEFT. The brake designated as LEFT travels on
the driverís side of the road.
Brake Line Installation
Use care in forming tubing to avoid sharp bends or
kinks. Use double flare steel tubing to assure tight
leakproof connections. This must be done by a
certified brake shop. Anchor all hydraulic lines at two
foot intervals to prevent chafing and vibration. Use
hydraulic rubber hose at points of flexing. Anchor
hose ends to avoid stress on tubing.
Brake Adjustment
Before removing the ground stand jacks, adjust the
brakes. Uni-servo brakes must be adjusted periodically
to assure having brakes when they are applied. Insert a
brake adjusting tool or a screwdriver into the slotted hole.
With the handle up and the bit down and against the
adjusting nut, pull down on the handle. While spinning
the wheel adjust the cog wheel up until you cannot rotate
the wheel forward. Then back off the adjusting wheel
twenty notches.
ALWAYS ROTATE DRUM IN DIRECTION OF
FORWARD ROTATION ONLY.
Brake Drum Maintenance
Brake drums must be reground if abnormal wear is
found, such as brake shoe hitting brake drum once
lining is gone, rivets hitting brake drums and or brake
drums out of round. NOTE: Maximum diameter al-
lowed 13.060"
Brake Set-up
1. Attach brake line to master cylinder outlet. Make sure
all connections are tight.
2. Fill the master cylinder from a sealed container of DOT
3 or 4 brake fluid. A pressure type brake bleeder may
be used. If one is not available, you can bleed the
system manually as follows.
3. After the master cylinder has been filled, remove the
flat spring behind the emergency lever. Pull forward on
the lever to pump the master cylinder. Use short
strokes until bubbling stops in the master cylinder.
Bleed the rear axle first. Install bleeder hose on the
bleeder valve on the first wheel with other end of the
hose in a clear container partially filled with brake fluid.
RIGHT (Double Flare)
WRONG
WARNING: To Prevent Serious Injury or Death
Saltwater, granular fertilizers and other corrosive materials are destructive to metal. To prolong
the life of a braking system used under corrosive conditions, we recommend that the actuator
be flushed periodically with a high pressure water hose. Be sure to re-grease bearings and oil
all moving parts after the unit has dried. At the end of the season, when unit is to be stored,
remove the brake drums and clean inside the brakes. Pack wheel bearings before drum is
installed.
Seitenansicht 9
1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16

Kommentare zu diesen Handbüchern

Keine Kommentare

Winchester-repeating-arms 101 podręczniki

Instrukcje obsługi i podręczniki użytkownika dla Sport i rekreacja Winchester-repeating-arms 101.
Dostarczamy 1 pdf podręczników Winchester-repeating-arms 101 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika






Więcej produktów i instrukcji dla Sport i rekreacja Winchester-repeating-arms

Modele Rodzaj dokumentu
70 (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms 70 (Historic Manual) User Manual, 31 strony
94 Top Tang Safety (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms 94 Top Tang Safety (Historic Manual) User Manual, 32 strony
9410 Top Tang Safety (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms 9410 Top Tang Safety (Historic Manual) User Manual, 44 strony
9422 (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms 9422 (Historic Manual) User Manual, 29 strony
1300 (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms 1300 (Historic Manual) User Manual, 34 strony
94 Cross Bolt Safety (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms 94 Cross Bolt Safety (Historic Manual) User Manual, 34 strony
9410 Cross Bolt Safety (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms 9410 Cross Bolt Safety (Historic Manual) User Manual, 40 strony
94 Pre 1992 (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms 94 Pre 1992 (Historic Manual) User Manual, 18 strony
9422 (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms 9422 (Historic Manual) User Manual, 30 strony
1886 Supplement (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms 1886 Supplement (Historic Manual) User Manual, 12 strony
1400 (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms 1400 (Historic Manual) User Manual, 19 strony
1886 (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms 1886 (Historic Manual) User Manual, 43 strony
63 (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms 63 (Historic Manual) User Manual [ru] , 23 strony
1200 (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms 1200 (Historic Manual) User Manual, 16 strony
Super X2 Sporting Supplement (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms Super X2 Sporting Supplement (Historic Manual) User Manual, 8 strony
Super X2 Practical Supplement (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms Super X2 Practical Supplement (Historic Manual) User Manual, 4 strony
Super X2 Practical Supplement (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms Super X2 Practical Supplement (Historic Manual) User Manual, 8 strony
Super X2 (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms Super X2 (Historic Manual) User Manual, 43 strony
Supreme (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms Supreme (Historic Manual) User Manual, 35 strony
BOSS (Historic Manual) Instrukcja Użytkownika   Winchester Repeating Arms BOSS (Historic Manual) User Manual, 15 strony